|
|
| Register | Forums | Blogs | Today's Posts | Search | Donate |
 |
 |
 |
|
#1
02-17-2013, 03:26 PM
|
|||||
|
|||||
Inside Ten-X Industries
Translation; Mine and Chuck's reloading room.
My side;  Chuck's side;  Tumbling, Trimming and pocket-cleaning table;  My electronic Dispenser system;  Powder/primer storage;   Photo of Obama; 
__________________
Diligentia, Vis, Celeritas COTEP#CBOB0428 NRA,GCA,OGCA, USAF,Msgt.(Ret.) Last edited by Dave Waits; 03-27-2013 at 09:12 PM. 
|
| The Following User Says Thank You to Dave Waits For This Useful Post: | ||
ronpaul50 (02-17-2013) | ||
|
#2
02-17-2013, 03:29 PM
|
|||||
|
|||||
|
very cool Dave. I need a bigger bench. I like the last pic. I wanna shoot a full auto Thompson
__________________
CBOB0405 ︻┳═一 “When you get to the end of your rope, tie a knot and hold on. Help is on the way.” Author Unknown
|
|
#3
02-17-2013, 03:34 PM
|
|||||
|
|||||
|
Nice setup, Dave! I wish I had that much room.
Tom
__________________
If you love wealth more than liberty, the tranquility of servitude better than the animating contest of freedom, depart from us in peace. We ask not your counsel nor your arms. Crouch down and lick the hand that feeds you. May your chains rest lightly upon you and may posterity forget that you were our countrymen. -- Samuel Adams COTEP CBOB0676 KO4ENQ
|
|
#5
02-17-2013, 09:34 PM
|
|||||
|
|||||
|
We built that room in Chuck's basement. We didn't even finish the inside Drywall!LOL! Bench is 8 feet long and 2 feet deep. All 2x8s and 4x4s. All fasteners are lagbolts,5/15ths.x2-1/2". One 2x6 crossbeam in center under table and all lags were countersunk. Those on the table were filled in with Clear Epoxy. Room measures 9'x12' inside. What isn't shown is a second wall Cabinet on Chuck's side for his powder/primers and his Gunsafe to the left of the Trimmer/Tumbler table.
Mike, both Powder measures are RCBS Uniflows, mine is a standard, Chuck's has the Micrometer charge-weight adjustment. My Rockchucker on the right, Chuck's RCBS, I think, Reloader Special press, on the left. his 505 scale on the left back of bench. The white Boxes and the large brown box on my side are full of bullets. The Pact Electronic sits right behind my side of the bench. The handiest piece of ewquipment outside of the Pact has to be the Lyman Electric trimmer. Has a PTO on the left side that takes screw in Primer-pocket brushes. You can clean a whole tray of case pockets in about four or five minutes with it.
__________________
Diligentia, Vis, Celeritas COTEP#CBOB0428 NRA,GCA,OGCA, USAF,Msgt.(Ret.) Last edited by Dave Waits; 02-17-2013 at 10:24 PM.
|
|
#6
02-17-2013, 09:47 PM
|
|||||
|
|||||
|
Really nice setup, Dave. I can't wait to get mine all set up. Once I do, I'll post pics, too.
__________________
Dan Wesson CCO NRA Member "The things that we fear are a weapon to be held against us." - Neil Peart
|
|
#7
02-17-2013, 09:50 PM
|
|||||
|
|||||
|
Nice!!
__________________
M H Davis COL USA Retired NRA Benefactor COTEP CCO0617 Eufaula, Alabama Isaiah 6:8-10. 8 Then I heard the voice of the Lord saying, "Whom shall I send? And who will go for us?" And I said, "Here am I. Send me!"
|
|
#8
02-17-2013, 09:57 PM
|
|||||
|
|||||
|
Cool Beans Dave,
__________________
CBOB:0002 1905 Savage 380, 1978, 1980 DW Pistol Pacs, Severns Custom 1985 Springer 1911A1, 09 DW Marksman, S&W Model 19-6, GSG 1911 22LR. , S&W Model 29-2
|
|
#10
02-18-2013, 08:38 AM
|
|||||
|
|||||
|
Looking good Dave!!
 Who shot the Thompson................I know that it was not a first timer!!!! 
__________________
"This is the 44 Magnum AutoMag and holds a 300 grain cartridge and if properly used can remove the fingerprints"!! COTEP # CBOB0152
|
Linear Mode
