COTEP.org  

Go Back   COTEP.org > Main Category > Reloading Bench

Reply
 
Thread Tools Display Modes
  #1  
Old 02-28-2012, 04:11 AM
douglas_knott's Avatar
douglas_knott douglas_knott is offline
Founding Member
COTEP Member
 
Join Date: Apr 2011
Location: Missouri
Posts: 3,378
Thanks: 623
Thanked 399 Times in 111 Posts
Default

Well that pretty well sums it up.

RCBS rock chucker
Lyman 49th
Powder trickler
Dies
RCBS 5-0-5 scale
ABC's of reloading
Digital Calipers
Brass, powder, primers, bullets
A RCBS powder drop will help speed up the process also
Did I miss anything?
__________________
CBOB0405
︻┳═一
“When you get to the end of your rope, tie a knot and hold on. Help is on the way.” Author Unknown
Reply With Quote
  #2  
Old 02-28-2012, 08:46 AM
titanse05's Avatar
titanse05 titanse05 is offline
Founding Member
COTEP Member
 
Join Date: Apr 2011
Location: Near Somerset, PA
Posts: 734
Thanks: 26
Thanked 31 Times in 7 Posts
Default

Start off by buying a couple of reloading books and study them. The ABCs of Reloading is a good one to start off with. http://www.amazon.com/ABCs-Reloading...0435851&sr=8-1

If you make it thru that book and still want to reload, then the fun begins. There are several good videos on youtube that I watched so I could see how the different presses functioned so I could choose the best one for my needs. I chose right off the bat to skip the single stage press because I wanted to buy the stuff I was going to use in the long term up front and not waste money on something to learn the process. I just used my progressive press as a single stage initially to learn how to adjust the dies and powder drop, then ran single cases thru while checking them, and finally moving up to using the press to it's full capablilities.

The top two progessive presses that are truly progressive and have 5 die stations are the Dillion 650 and the Hornady Lock-n-load. I ended up picking the Hornady Lock-n-load Progressive press and I'm very glad that I did. I've reloaded over 3k rounds with it so far. Things that I liked about the LNL over the 650 was that the case placement and bullet seating both took place on the left side of the press. My left hand handles the case and bullet, and my right hand never leaves the press handle. Also, the location of the bullet seating is in the front of the press and provides an unobstructed view of the amount of powder in the case so I can check each one visually.

The best advice is to use all of the available research material, books and the internet, to look at the different presses and get a basic understanding of the process. Then dive in with both feet if its something that you think that you can handle and enjoy.
__________________
CBOB0235
Reply With Quote
  #3  
Old 02-28-2012, 08:57 AM
AutoMag's Avatar
AutoMag AutoMag is offline
Founding Member
COTEP Member
 
Join Date: Apr 2011
Posts: 4,697
Thanks: 154
Thanked 263 Times in 74 Posts
Default

All of the above info is right on!!

Start out small, I mean a single stage press in case reloading is not for you. If it is then you can progress later on to a Dillon or the like!!

About the best info I can offer is to reload in a room by yourself and free from noise if you can. The least little sounds or disturbances can be distracting. Really by sounds I mean the TV, radio or friends or family members talking to you!!

A double charge or an under charge can both cause devastating results!!

I am anal in my reloading in that I crank out 10 rounds on my Dillon RL550B and then mic and check the weight on EVERY one!!!
__________________
"This is the 44 Magnum AutoMag and holds a 300 grain cartridge and if properly used can remove the fingerprints"!!


COTEP # CBOB0152
Reply With Quote
  #4  
Old 02-28-2012, 09:15 AM
ArmyVetSgt.Adkins's Avatar
ArmyVetSgt.Adkins ArmyVetSgt.Adkins is offline
Founding Member
COTEP Member
 
Join Date: Aug 2011
Location: Bellevue Ohio
Posts: 61
Thanks: 2
Thanked 0 Times in 0 Posts
Default

A big Thank You to everyone that has responded and I forgot to mention that I did in advance buy 3 reloading books one being the ABC's of reloading and I think that I will definitely go the route of A single stage press to begin with,would you recommend the lee or the RC BS single stage press?After the press I just need A set of Carbine Dies correct?Do I need 3 PC or the 4 PC die set?I have A high quality set of digital calipers in my possession already I guess I still would need A scale also..
Thanks again to everyone I just love this place and will start being more active in the Forum as I have been out foe awhile as I had to have A Bowel Resection for my Crohns Disease and I had multiple complications from the initial surgery that resulted in me having two additional surgeries on top of that and I'm actually still in the Hospital right now but hope to be released real soon...This forum has made my stay in the hospital A little more bare able by being able to read and keep up on my favorite Hobby
__________________
CBOB#0525
Army Vet.
Wilson Cqb Elite
Reply With Quote
  #5  
Old 02-28-2012, 10:13 AM
skosh69's Avatar
skosh69 skosh69 is offline
Founding Member
COTEP Member
 
Join Date: Apr 2011
Posts: 11,000
Thanks: 2,242
Thanked 4,520 Times in 1,212 Posts
Default

Congrats to you for taking interest in reloading...

Whatever press setup you get, just remember to always make sure there's powder in the cases before seating the bullet, otherwise you'll be known as "Mr. Squib", like me...hehehehe

There's your reloading safety tip for the day.......

PS, I recommend the RCBS Rock Chucker Supreme kit, it has everything you need, minus the dies and a tumbler!
Reply With Quote
  #6  
Old 02-28-2012, 10:19 AM
douglas_knott's Avatar
douglas_knott douglas_knott is offline
Founding Member
COTEP Member
 
Join Date: Apr 2011
Location: Missouri
Posts: 3,378
Thanks: 623
Thanked 399 Times in 111 Posts
Default

Three die, the fourth die is a factory crimp. Some people use them but they only fix something that should have been taken care of in step three. Hope you get to feeling better. We are thinking and praying for your speedy recovery.
__________________
CBOB0405
︻┳═一
“When you get to the end of your rope, tie a knot and hold on. Help is on the way.” Author Unknown
Reply With Quote
  #7  
Old 02-28-2012, 01:00 PM
Big Smoke's Avatar
Big Smoke Big Smoke is offline
Founding Member
COTEP Member
 
Join Date: Feb 2012
Location: Rockville, Maryland
Posts: 337
Thanks: 5
Thanked 0 Times in 0 Posts
Default

I second the idea of reading all the information in the ABC's of Reloading, or a good reloading book. That's how I started, and found a guy who was selling his Dillon 550b and was getting out of reloading. I bought the press, tumbler, separator, dies, and some other miscellaneous items for $400, but that was over 20 years ago.
But knowing I was using a progressive reloader, I really had to mind my P's and Q's. I would (and still do) check every 10th round to make sure the charge is right and check the Overall Length (O.A.L.) of the cartridge for consistency. I use separate dies for seating and crimping. Some dies will do both.
I can definitely understand going the single stage route, especially if you are new to reloading. But if you have 1000 rds a month to do, that's going to take the whole month to do. You CAN start with a progressive as long as you understand exactly what each stage does, and keep a check on it for consistency, and don't have any distractions around you while your doing it.
Reply With Quote
  #8  
Old 02-28-2012, 07:24 PM
DaFadda's Avatar
DaFadda DaFadda is offline
Founding Member
Super Moderator
 
Join Date: Dec 2011
Location: Nashville Tennessee
Posts: 3,360
Thanks: 665
Thanked 611 Times in 169 Posts
Default

I'll weigh in here Sarge,

+1 to everything you see above. All the answers are "spot on."

My first press is the RCBS Rockchucker. It is everything a single stage press should be. It will outlive you, your children AND your grandchildren. The Rockchucker Supreme kit has all the tools you need. Weigh scale, press, powder dispenser, cartridge holders. All you need extra are the carbide dies and the shell holders. I still use the RCBS for 5.56/.223 rounds. $269 at Cabelas.

http://www.cabelas.com/product/RCBS-...h-All+Products

All this said..... my Second press is

The Lee Classic Turret Press.

http://www.cabelas.com/presses-dies-...:referralID=NA
It is a four hole turret press that will work in auto mode, OR single stage. A turret press is "inbetween" a single stage and a progressive. You CAN use the turret in auto mode and make one cartridge at a time. OR... you can set up the deprime die, the flaring die and the seating die and work in batch mode. The turrets are removable so that you can have your .45 dies set up, then with a simple twist, install the .223 dies for rifle. I bought the Classic fourhole turret for $89 on sale at Cabelas. That was the press and one turret only since I already owned the scales and powder charger. Additional turrets are about 10 bucks or so at Cabelas on sale, or 12.99 at Midway. The advantage for me is that once I have a setup for .45, and have locked it in... I NEVER have had to make an adjustment. Done is done.

I PREFER to do my reloading in "batch mode." Meaning that I spend a night priming 500 or so rounds. Next night I bell/flare the rounds, following night I load powder and seat.... following it ALL up with checking each round with a Dillon or Wilson depth and seating gage ( a DEFINITE PURCHASE). They are about 15 bucks per caliber, and worth every cent to a new reloader.

If you can find a special on the Lee Classic 4 Hole Turret press WITH a package i.e. scales and powder measure... I would go that route. If you can't, you will NEVER go wrong with the RCBS Rockchucker Supreme. My actual preference, since I like the RCBS Scale and Powder measure, would be to purchase the RCBS Rockchucker Supreme above, learn the system, then buy a Lee Turret. Gee... wonder why.... OH... that's exactly what I did!

OH!!!! And if you go the RCBS route... CALL RCBS direct. They usually have Rockchucker Supreme kits as Refurbished at a discount!

Just sayin'
Da
__________________
COTEP: CBOB578
DW CCO
SIG GSR 1911
SA Micro Compact
and a spectacular cast of others!

"You have never lived, until you have almost died. And for those who fight for it, life has a flavor that the protected will never know." Guy de Maupassant, 1893.
Anonymously, penned on a sign at a command post at Khe Sanh, RVN.

Last edited by DaFadda; 02-28-2012 at 07:38 PM.
Reply With Quote
Reply

Thread Tools
Display Modes



All times are GMT -4. The time now is 03:13 AM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.